新闻动态

耐斯机械民族品牌合模机，翻模机，立式合模机，压板立式合模机，磁盘立式合模机动作流程分解

动作流程

Ⅲ.Work flow

{C}1、 {C}将下工作台移出，把模具吊入并放置于下工作台中央（如下图所示）Move out the lower working bench and lift up the mold and place it in the center of the lower working bench (as shown in the following diagram)

{C}2、 {C}将下工作台移入机架中（如下图所示）Move the lower working bench back to the rack (as shown in the following diagram)

{C}3、 {C}将滑台及上工作台下行到模具上表面并使用压板 (磁盘式的只需进行充磁) 将上下模具分别固定在上工作台与下工作台上。（如下图所示）Lower the slide platform and the upper working bench to the upper surface of mold and use clamp (magnetizing is only need for magnetic type) to fix the upper and counter die at the upper working bench and lower working bench respectively. (as shown in the following diagram)

{C}4、将滑台及上工作台上移，将模具打开。（如下图所示）

Raise the slide platform and upper working bench and open the mold. (as shown in the following diagram)

{C}5、 {C}将下工作台移出，此时可配红丹（如下图所示）

Move the lower working bench out and red lead may be at this moment (as shown in the following diagram)

{C}{C}

{C}6、 {C}将配好红丹的模具移回机架中，上工作台下降，合上模具后根据需要选择压力进行加压，一般加压以二次为宜（如下图所示）

Move back the mold with prepared red lead to the rack, lower the upper working bench. Increase the pressure according to the selected pressure after closing the mold. Two times of pressurization is suitable generally (as shown in the following diagram)

{C}{C}

备注：加压功能仅适用合模机！Note: the compression function is only applicable to the die casting machine!

{C}7、加压完成后，上工作台上升，下平台移出（如下图所示）

After pressurization is completed, the upper working bench rises and the lower working bench moves out (as shown in the following diagram)

{C}8、 {C}滑台及上工作台下移，使上工作台翻转180°此时上模上翻，可根据红丹的情况进行修模，反复进行上面的操作，直到模具修好为止（如下图所示）When the sliding platform and lower working bench move downwards, the upper working bench rotates 180°. The upper die upturns. Mold can be repaired according to the location of red lead. Repeat the above operation until the mold is repaired (as shown in the following diagram)

{C}9、 {C}模具修好后，将模具移入机架中并将上平台下降，稍加压后将模具的固定螺丝拆卸(磁盘式的此时进行退磁)，上平台上升，下平台移出，吊走模具（如下图所示）After the mold is repaired, move it to the rack and lower the upper platform. After slight pressurization, dismantle the fixing screw of the mold (demagnetization should be performed for the magnetic type). The upper platform rises and the lower platform moves out. Lift the mold away (as shown in the following diagram)

上一篇：耐斯民族品牌合模机，翻模机，压板合模机，磁盘合模机，立式合模机产品结构示意图
下一篇：磁盘合模机、压板合模机、立式合模机、龙门合模机常规参数

新闻动态

新闻动态

耐斯机械民族品牌合模机，翻模机，立式合模机，压板立式合模机，磁盘立式合模机动作流程分解

相关信息